We have just what you are looking for.
Starting with the bearing kit you will need the Bearing Kit # BK2-100 which includes inner bearing # L68149, outer bearing # L44649, grease seal # 10-19, the races, washer, and cotter pin for the 3500lb Lippert axle on your 2008 Coachmen Adrenaline Blast 210MPH, but does not include the castle nut.
For a castle nut 3500lb axles typically use a 1" diameter nut but you will want to measure your spindle to be sure. If this is the case then you will... view full answer...
There are a lot of great solutions to your problem, but to upgrade your trailer axles from 6,000 lbs to 7,000 lbs, you need to replace your axles entirely. Adding higher capacity hubs alone won't change the weight capacity of your axles. Note that even if you decide to upgrade your axles, you still might be limited by the weight capacity of your trailer frame or coupler as these could be rated less than your axle capacity.
To upgrade your axles, I recommend a full kit that includes a 7,000... view full answer...
The Voyager 2.0 like the # ASA37YR does support up to four cameras. However, the only option is to add the # ASA64YR. There are no true sidemarker cameras available. The Furrion Vision S Wireless RV Backup Camera System w/ 3 Cameras # FCE48TASL-05 would give you the side cameras you're looking for and you can add # FCN48TASF for the 4th camera.
Installation isn't too difficult. You will need to remove the Voyager bracket and cut off the connector. After that, you will hardwire the Furrion... view full answer...
There is not an issue with installing the grease seal # 9103309 you were looking at 1/16" below the face of the hub. It will still seal against the grease seal surface on your axle, though you will want to make sure to not force the seal down to far as you can press it down against the bearing and race and cause issues there.
I included a video showing the grease seal, inner bearing and race, and outer bearing and race being installed on on a hub for you to take a look at. view full answer...
The Ultra-Fab Deluxe Electric Landing Gear Set, # UF17-943010 is not designed for an alternate orientation of how the electric motors mount. If you let us know what your current part number is we can look for a suitable replacement. view full answer...
Per conversation with Lippert, the Lippert Components Tuson High Speed 5th Wheel RV Landing Gear Motor # LC141893 is a compatible replacement for the 1-065-041012-01 electric motor you listed. view full answer...
The ground (cold side) of the brake light signal in a Sprinter can sometimes be found in the wiring above the brake pedal. A high-sensitivity LED circuit tester will be required to test this due to the weak signal strength in this wire. This is due to the low voltages in this vehicle's wiring system.
In other cases you may need to install an accessory stop light switch kit # RM-751475 to provide that brake light signal needed to trigger a brake controller like the Prodigy P3 # 90195. view full answer...
Per the Installation and Operation Guide for the Progressive Dynamics Pure Sine Wave Inverter w/ Transfer Switch, # PD44FR it references using Romex and pushing the conductor into place. This states using lugs instead of ring terminals. I suggest using 12 gauge. view full answer...
To use with the Dexter Equalizer for 2-1/2" Wide Slipper Springs # 13-141-3 I recommend using the 1" diameter Suspension Bolt # 7-136-2-6-112 for the center/hanger bolt and the 3/4" diameter # 126A1 for the spring bolt. Both options are wet bolts with integrated grease zerks to allow for easy maintenance. view full answer...
The Valterra Bladex 1-1/2" Diameter Waste Valve # T1001VP and the 24" Extension Tube # TX24HPB would be all that you need for the setup you're looking for. The waste valve isn't available with this length extension tube already attached.
On the Valterra Waste Valve the existing rod can simply be unscrewed from the main housing and the new threaded 24" extension would be screwed onto the unit in its place. view full answer...
Go To Results